DLB Propeller 5 is an indoor wireless device that supports W52 band at 5GHz and can be used as a wireless LAN access point or bridge.
It supports a wide operating temperature of -40 to + 65℃, can be installed in places with severe temperature conditions such as frozen warehouses and factory buildings.
This product is RoHS compliant.
– Want to use it in places with severe temperature conditions such as frozen warehouses and factory buildings, or in places where power wiring is difficult.
→Wide operating temperature from -40 to + 65℃.
→Supports PoE (original method) and can be used in places where it is difficult to wire the power supply to the terminal.
– Use for both wireless LAN-AP and bridge applications.
→Can be used with either AP / bridge depending on the installation orientation.
– Easy introduction.
→Low cost and no additional license required
(For vertical installation) (Mainly for AP)
Up and down 15°/ left and right 60°
| Product name | DLB Propeller 5 |
| Product code | 181-FN-004 |
| Wireless LAN Interface | IEEE802.11a/n iPoll2/3 (Original method) |
| Wired LAN Interface | RJ-45 (10/100BASE-TX) x1port – Automatic detection 10/100BASE-TX Full/Half duplex – Auto MDI/MDI-X Function – Power Over Ethernet PD (Original method) |
| Antenna type, gain | Directional panel antenna x2 (MIMO) 5GHz band : 15dBi |
| Security | WEP, WPA/WPA2 Personal, WPA/WPA2 Enterprise, WMM, WACL |
| Protocol | DHCP, NTP, SNMP v1, HTTP, HTTPS, VLAN |
| Modulation technology | OFDM |
| Modulation method | 802.11a/n : OFDM (16/64QAM, QPSK, BPSK) |
| Frequency band | 5.180～5.700GHz |
| Bandwidth | 20/40MHz |
| Maximum communication speed | 802.11a : 54Mbps 802.11n : 300Mbps |
| Number of channels | Up to 19 channels |
| Number of SSID registrations | 8 |
| Action mode | AP, Station |
| Maximum transmit power | 7dBm (W52/W53) 14dBm (W56) |
| Reception sensitivity | -97～75dBm |
| Management function | HTTP/HTTPS |
| Power supply | DC12～24V *Use the included PoE adapter or optional power supply |
| Power consumption | 4.5W (Maximum) |
| Operating temperature | Main body : -40～+65℃ Dedicated PoE adapter : -10～+50℃ |
| Operating humidity | 0～90% (No condensation) |
| Storage temperature | -40～+65℃ |
| Size | (W) 175 x (H) 29 x (D) 65 mm (Does not include protrusions) |
| Weight | 94g (only a main body) |
| Installation method | Wall mount, Prop mount |
| Waterproof and dustproof performance | IP55 |
| Certification | TELEC (Certification number : 206-000527) VCCI ClassB, FCC, CE Marking, RoHS |
| Accessories | Insertion bracke x1 Installation bracket x1 Cable ties x2 Wall mounting screws (M3.5 x32) & anchors x1 Dedicated PoE adapter x1 AC cable x1 |
| Product warranty period | 1year |
| Optional Power supply | |||
| Product name | 802.3 af to 24V Gigabit PoE Converter | DC9-36 to DC24 Giga PoE Injetor HPI-3201G-DC |
|
| Product code | 174-FN-002 | 174-HY-001 | |
| Standard | IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE802.3ab 1000BASE-T |
IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T |
|
| Interface | DATA + PoE Out (24VDC) |
RJ-45 10/100/1000BASE-T x1port DC24V output |
－ |
| DATA+PoE In (802.3af/at) |
RJ-45 10/100/1000BASE-T x1port IEEE802.3af/at (PD) |
－ | |
| DATA+POWER (OUT) |
－ | RJ-45 10/100/1000BASE-T x1port DC24V output |
|
| DATA (IN) | － | RJ-45 10/100/1000BASE-T x1port | |
| Power supply | DC jack | － | φ2.1 x 5.5mm |
| Terminal block | － | Usable wire diameter : AWG14～28 Peeling margin range : 6～7mm |
|
| DC terminal input voltage | DC36～60V (Terminal polarity automatic recognition) | － | |
| PoE Input voltage | DC36～60V | DC9～36V | |
| Output voltage | DC24V | ||
| Output power | 13W (Maximum) | 12W (Maximum) | |
| Power consumption | － | 20W (Maximum) | |
| Size (Does not include protrusions) | (W) 117 x (H) 34 x (D) 86 mm | (W) 71 x (H) 22 x (D) 66 mm | |
| Weight | 300g | 140g | |
| Operating temperature | -20～+65℃ | -20～+60℃ | |
| Operating humidity (No condensation) | 0～90%RH | 10～90%RH | |
| Storage temperature | -40～+85℃ | -20～+85℃ | |
| Certification | RoHS | ||
| Product warranty period | 1year | ||
| Accessories | DIN rail metal fittings (installed on the main body) x1 | Power terminal block x1 | |
Propeller installation method using PoE converter and PoE extension device .
Pattern characteristics
